Integrating microalgae growth in biomethane plants: Process design, modelling, and cost evaluation.

The integration of microalgae cultivation in anaerobic digestion (AD) plants can take advantage of relevant nutrients (ammonium and ortho-phosphate) and CO2 loads. The proposed scheme of microalgae integration in existing biogas plants aims at producing approximately 250 t·y-1 of microalgal biomass, targeting the biostimulants market that is currently under rapid expansion. A full-scale biorefinery was designed to treat 50 kt·y-1 of raw liquid digestate from AD and 0.45 kt·y-1 of CO2 from biogas upgrading, and 0.40 kt·y-1 of sugar-rich solid by-products from a local confectionery industry. An innovative three-stage cultivation process was designed, modelled, and verified, including: i) microalgae inoculation in tubular PBRs to select the desired algal strains, ii) microalgae cultivation in raceway ponds under greenhouses, and iii) heterotrophic microalgae cultivation in fermenters. A detailed economic assessment of the proposed biorefinery allowed to compute a biomass production cost of 2.8 ± 0.3 €·kg DW-1, that is compatible with current downstream process costs to produce biostimulants, suggesting that the proposed nutrient recovery route is feasible from the technical and economic perspective. Based on the case study analysis, a discussion of process, bioproducts and policy barriers that currently hinder the development of microalgae-based biorefineries is presented.

Roadmap on thermoelectricity.

The increasing energy demand and the ever more pressing need for clean technologies of energy conversion pose one of the most urgent and complicated issues of our age. Thermoelectricity, namely the direct conversion of waste heat into electricity, is a promising technique based on a long-standing physical phenomenon, which still has not fully developed its potential, mainly due to the low efficiency of the process. In order to improve the thermoelectric performance, a huge effort is being made by physicists, materials scientists and engineers, with the primary aims of better understanding the fundamental issues ruling the improvement of the thermoelectric figure of merit, and finally building the most efficient thermoelectric devices. In this Roadmap an overview is given about the most recent experimental and computational results obtained within the Italian research community on the optimization of composition and morphology of some thermoelectric materials, as well as on the design of thermoelectric and hybrid thermoelectric/photovoltaic devices.

Microbial conversion of carbon dioxide and hydrogen into the fine chemicals hydroxyectoine and ectoine.

This study explores a novel conversion of CO2 into the chemicals hydroxyectoine and ectoine, which are compounds with high retail values in the pharmaceutical industry. Firstly, 11 species of microbes able to use CO2 and H2 and that have the genes for ectoines synthesis (ectABCD) were identified through literature search and genomic mining. Laboratory tests were then conducted to ascertain the capacity of these microbes to produce ectoines from CO2. Results showed that the most promising bacteria for CO2 to ectoines bioconversion areHydrogenovibrio marinus, Rhodococcus opacus, and Hydrogenibacillus schlegelii.Upon salinity and H2/CO2/O2 ratio optimization,H. marinus accumulated 85 mg of ectoine g biomass-1. Interestingly, R.opacusand H. schlegelii mainly produced hydroxyectoine (53 and 62 mg g biomass-1), which has a higher commercial value. Overall, these results constitute the first proof of a novel valorization platform of CO2 and lay the foundation for a new economic niche aimed at CO2 recircularization into pharmaceuticals.

Tungsten disulfide nanotubes enhance flow-induced crystallization and radio-opacity of polylactide without adversely affecting in vitro toxicity.

Treatment of vascular disease, from peripheral ischemia to coronary heart disease (CHD), is poised for transformation with the introduction of transient implants designed to "scaffold" regeneration of blood vessels and ultimately leave nothing behind. Improved materials could expand the use of these devices. Here, we examine one of the leading polymers for bioresorbable scaffolds (BRS), polylactide (PLA), as the matrix of nanocomposites with tungsten disulfide (WS2) nanotubes (WSNT), which may provide mechanical reinforcement and enhance radio-opacity. We evaluate in vitro cytotoxicity using vascular cells, flow-induced crystallization and radio-opacity of PLA-WSNT nanocomposites at low WSNT concentration. A small amount of WSNT (0.1 wt%) can effectively promote oriented crystallization of PLA without compromising molecular weight. And radio-opacity improves significantly: as little as 0.5 to 1 wt% WSNT doubles the radio-opacity of PLA-WSNT relative to PLA at 17 keV. The results suggest that a single component, WSNT, has the potential to increase the strength of BRS to enable thinner devices and increase radio-opacity to improve intraoperative visualization. The in vitro toxicity results indicate that PLA-WSNT nanocomposites are worthy of investigation in vivo. Although substantial further preclinical studies are needed, PLA-WSNT nanocomposites may provide a complement of material properties that may improve BRS and expand the range of lesions that can be treated using transient implants. STATEMENT OF SIGNIFICANCE: Bioresorbable Scaffolds (BRSs) support regeneration of arteries without permanent mechanical constraint. Poly-L-lactide (PLLA) is the structural material of the first approved BRS for coronary heart disease (ABSORB BVS), withdrawn due to adverse events in years 1-3. Here, we examine tungsten disulfide (WS2) nanotubes (WSNT) in PLA to address two contributors to early complications: (1) reinforce PLLA (enable thinner BRS), and (2) increase radiopacity (provide intraoperative visibility). For BRS, it is significant that WSNT disperse, remain dispersed, reduce friction and improve mechanical properties without additional chemicals or surface modifications. Like WS2 nanospheres, bare WSNT and PLA-WSNT nanocomposites show low cytotoxicity in vitro. PLA-WSNT show enhanced flow-induced crystallization relative to PLA, motivating future study of the processing behavior and strength of these materials.

Toward a Reversible Consolidation of Paper Materials Using Cellulose Nanocrystals.

An innovative consolidation strategy for degraded paper is presented based on the reversible application of cellulose nanocrystals as sustainable fillers to reinforce mechanical properties and resistance to further degradation. The compatibility and efficacy of the proposed consolidation treatment are assessed first on pure cellulose paper, used as a model, by reliable techniques such as field emission scanning electron microscopy, atomic force microscopy, tensile tests, X-ray powder diffraction, and Fourier transform infrared spectroscopy, evidencing the influence of the surface functionalization of nanocellulose on the consolidation and protection effects. Then, the consolidation technique is applied to real aged paper samples from Breviarium romanum ad usum Fratrum Minorum S.P. (1738), demonstrating the promising potential of the suggested approach. Amperometric measurements, carried out with a smart electrochemical tool developed in our laboratory, demonstrate the reversibility of the proposed treatment by removal of the nanocrystalline cellulose from the paper surface with a suitable cleaning hydrogel. This completely new feature of the consolidation treatment proposed here satisfies a pivotal requisite in cultural heritage conservation because the methodological requirement for the ″reversibility″ of any conservation measure is a fundamental goal for restorers. A paper artifact, in fact, is subject to a number of natural and man-made hazards, inducing continuous degradation. With time, monitoring and consolidation actions need to be often performed to ensure conservation, and this tends to modify the status quo and compromise the artifact integrity. Removable treatments can potentially avoid erosion of the artifact integrity.

Tailoring water stability of cellulose nanopaper by surface functionalization.

Cellulose nanopaper (CNP) features appealing properties, including transparency, flatness, a low thermal expansion coefficient and thermal stability, often outperforming conventional paper. However, free-standing crystalline cellulose films usually swell in water or upon moisture sorption, compromising part of their outstanding properties. This remains a major problem whenever working in a water environment is required. Freestanding cellulose nanopaper is prepared by solution casting water suspensions of cellulose nanocrystals with an average width of 10 nm and an average aspect ratio of 28, isolated from Avicel by acid hydrolysis and extensively characterized by AFM and FE-SEM measurements and GPC detection of their degree of polymerization. We demonstrate by elemental analyses, FT-IR, Raman spectroscopy, XRD measurements and water contact angle detection that wet treatment with lauroyl chloride results in surface hydrophobization of nanopaper. The hydrophobized nanopaper, C12-CNP, shows a more compact surface morphology than the starting CNP, due to the effect of chemical functionalization, and presents enhanced resistance to water, as assessed by electrochemical permeation experiments. The new hydrophobized nanopaper is a promising substrate for thin film devices designed to work in a humid environment.

CdS-polymer nanocomposites and light-emitting fibers by in situ electron-beam synthesis and lithography.

A straightforward, electron-beam induced synthesis and patterning approach to the in situ generation of CdS nanocrystals in nanocomposite films and light-emitting electrospun nanofibers is used. Smartly combining room-temperature nanoimprinting, electrospinning, and electron-beam decomposition of nanocrystal precursors and subsequent nucleation of nanoparticles in a polymer matrix allows exploitation of the most favorable flow conditions of organics to produce various nanocomposite nanostructures.

Light-emitting nanocomposite CdS-polymer electrospun fibres via in situ nanoparticle generation.

We report on the simple, in situ generation of CdS nanocrystals inside electrospun polymer fibres by thermal decomposition of a cadmium thiolate precursor, leading to nanocomposite light-emitting fibres. The modifications induced in the precursor by the thermal decomposition are investigated by a morphological, structural and spectroscopic analysis of the resulting nanocomposite fibres. This approach allows us to overcome nanofabrication difficulties related to disfavoured micro- or nanofluidic molecular flow as given by the direct incorporation of particles in the electrospinning solution. This method therefore enables the synthesis of luminescent, CdS-based composite fibres with emission peaked in the visible range, suitable as building blocks for nanophotonic devices based on light-emitting nanomaterials.

Patterning of light-emitting conjugated polymer nanofibres.

Organic materials have revolutionized optoelectronics by their processability, flexibility and low cost, with application to light-emitting devices for full-colour screens, solar cells and lasers. Some low-dimensional organic semiconductor structures exhibit properties resembling those of inorganics, such as polarized emission and enhanced electroluminescence. One-dimensional metallic, III-V and II-VI nanostructures have also been the subject of intense investigation as building blocks for nanoelectronics and photonics. Given that one-dimensional polymer nanostructures, such as polymer nanofibres, are compatible with sub-micrometre patterning capability and electromagnetic confinement within subwavelength volumes, they can offer the benefits of organic light sources to nanoscale optics. Here we report on the optical properties of fully conjugated, electrospun polymer nanofibres. We assess their waveguiding performance and emission tuneability in the whole visible range. We demonstrate the enhancement of the fibre forward emission through imprinting periodic nanostructures using room-temperature nanoimprint lithography, and investigate the angular dispersion of differently polarized emitted light.

Two dimensional patterning of fluorescent proteins in hydrogels.

This work describes the successful micropatterning of hybrid systems consisting of hydrogel-dispersed optically active and controllable proteins on solid surfaces without degradation of the photophysical properties of the light-emitting biomolecules. It demonstrates the preservation of the luminescence properties of proteins entrapped into isolated microstructures of poly(acrylamide) gel. This way we can exploit both the structural and function-preserving properties of the hydrogels and the functionality of light-emitting proteins. We believe that this approach can open the way to the realization of nanopatterned optical memories based on photochromic biomolecules.

Multilevel, room-temperature nanoimprint lithography for conjugated polymer-based photonics.

We demonstrate the multilevel patterning of organic light-emitting polymers by room-temperature nanoimprint lithography (RT-NIL), which is impossible to obtain by conventional hot embossing. In particular, we realize one- and two-dimensional photonic crystals with 500 nm periodic features and investigate the changes in the optical properties (luminescence and quantum yield) of the organic active layer. An increase of the quantum yield by 2.4% for the patterned film with respect to the untextured one and the enhancement of the output light emitted at a particular angle (Theta = 69 degrees) are observed for gratings whose Bragg periodicity matched the emission wavelength of the polymer. The employment of RT-NIL to pattern polymer semiconductors without degradation of their optical properties represents a strategic route for the realization of novel nanopatterned optoelectronic devices.

Rapid soft lithography by bottom-up enhanced capillarity.

The growing demand for new solutions to pursue the trend of micro- and nanoelectronics predicted by Moore's law is stimulating the development of new high-resolution, low-cost lithographies. Here we demonstrate that several bottom-up approaches can be used to increase the throughput of soft lithography by exploiting the enhanced hydrophilicity, the low viscosity, and the fragility of the employed materials. In particular, the customized functionalization of the involved surfaces to improve the wettability to polymer fluids and the dramatic decrease of the viscosity of polymer compounds as the temperature is increased, together with the good thermal stability of the functionalized surfaces, allow a faster filling of elastomeric channels, up to almost an order of magnitude with respect to conventional microfluidics.

Self-assembled extracellular matrix protein networks by microcontact printing.

Physiological patterns of the extracellular matrix protein, laminin-1, were obtained on glass substrates by physisorption-assisted microcontact printing. Besides the well-retained antigenicity confirmed by indirect immunofluorescence assays, we investigated the supramolecular organization of the proteins by atomic force microscopy. We found the characteristic protein self-assembling in polygonal networks with well-defined sub-100 nm quaternary structures of laminin. The formation of these physiological mesh-like protein matrices was obtained by means of one-step soft lithography without any preliminary functionalization of glass, which can be exploited for many possible applications for cell cultures and biomolecular devices.